DIGITAL WIRELESS NOTICE BOARD

-

 VIDEO:


VIDEO LINK:                          https://youtu.be/6k2U68cVIWg


COMPONENTS REQUIRED:

1.ARDUINO NANO

2.16X2 LCD DISPLAY

3.BLUETOOTH MODULE

4.BREAD BOARD

5.JUMPER CABLES


CODE:

//Creative Pradeep//

//Simple App Controlled LCD Notice Board


#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x3F,16,2);  //Change the HEX address


#include <SoftwareSerial.h>

SoftwareSerial mySerial (2, 3);   //(RX, TX);


String val = "No Data";

String oldval;

String newval = "No Data";

int i = 0;


void setup() 

{

  // put your setup code here, to run once:

  lcd.init();

  lcd.backlight();

  mySerial.begin(9600);

  Serial.begin(9600);

  lcd.setCursor(0, 0);

  lcd.print("    Digital    ");

  lcd.setCursor(0, 1);

  lcd.print(" Notice  Board ");

  delay(3000);

  lcd.clear();

}


void loop() 

  {

  val = mySerial.readString();

  val.trim();

  Serial.println(val);

  if(val != oldval)

  {

    newval = val;

  }

  val = oldval;

Serial.println(val);

lcd.clear();

lcd.setCursor(16, 1);

lcd.print(newval);

lcd.setCursor(16, 0);

lcd.print("Notice:");

for(int counter = 0; counter < 24; counter++)

{

lcd.scrollDisplayLeft();

delay(500);


}

}

APP LINK:

APP DOWNLOAD

CIRCUIT DIAGRAM:


CHANNEL LINK :         :www.youtube.com/c/CreativePradeep

Comments

Post a Comment

Popular posts from this blog

SMART WIFI CONTROLLED DOOR LOCK SYSTEM USING ESP32

-
Image
  VIDEO: VIDEO LINK: https://youtu.be/dVWisvdzj5I COMPONENTS REQUIRED: 1.ESP32 2.12V SOLENOID LOCK 3.5V RELAY MODULE 4.WIRES 5.BATTERY CIRCUIT DIAGRAM: 1. Vcc of relay to 3v of esp32 2.Gnd to Gnd 3.Signal pin of relay to D23 pin of esp32 Blynk App Setting: First select a switch and select the virtual pin V1 for that switch then click on ok CODE: https://docs.google.com/document/d/1XYxz6jcs-zJjwO9RT5ND8UxTQSkNdYqc7UR5PlpOId4/edit?usp=drivesdk CHANNEL LINK: https://youtube.com/c/CreativePradeep
Read more

ARDUINO PULSEOXIMETER

-
Image
     VIDEO: VIDEO LINK:                             https://youtu.be/ssOLHjx0Axo COMPONENTS REQUIRED: 1.ARDUINO NANO 2.MAX30100 PULSEOXISENSOR 3.4.7K RESISTOR 4.OLED DISPLAY 5.BREAD BOARD CODE: //CREATIVE PRADEEP// //ARDEUINO PULSEOXIMETER// #include <Wire.h> #include "MAX30100_PulseOximeter.h" #include <Adafruit_GFX.h> #include <Adafruit_SSD1306.h> #define ENABLE_MAX30100 1 #define SCREEN_WIDTH 128 // OLED display width, in pixels #define SCREEN_HEIGHT 32 //64 // OLED display height, in pixels // Declaration for an SSD1306 display connected to I2C (SDA, SCL pins) // The pins for I2C are defined by the Wire-library. // On an arduino UNO:       A4(SDA), A5(SCL) // On an arduino MEGA 2560: 20(SDA), 21(SCL) // On an arduino LEONARDO:   2(SDA),  3(SCL), ... #define OLED_RESET    4 // 4 // Reset pin # (or -1 if sharing Arduino reset pin) #d...
Read more

SERVO CONTROL USING JOYSTICK MODULE

-
Image
 VIDEO: VIDEO LINK:    https://youtu.be/Xxs-a0JTmcA COMPONENTS REQUIRED: 1.JOYSTICK MODULE 2.ARDUINO NANO 3.SERVO MOTOR 4.BREAD BOARD 5.JUMER CABLES CODE: //CREATIVE PRADEEP// #include <Servo.h> const int Y_pin = A0; // analog pin connected to Y output Servo myservo;   int val;     void setup() {   myservo.attach(7);  } void loop() {   val = analogRead(Y_pin);               val = map(val, 0, 1023, 0, 180);        myservo.write(val);                     delay(15);                            } CIRCUIT DIAGRAM: CHANNEL LINK:                       www.youtube.com/c/CreativePradeep
Read more